![nra winchester model 25 assembly instructions nra winchester model 25 assembly instructions](https://slideplayer.com/16194638/95/images/slide_1.jpg)
![nra winchester model 25 assembly instructions nra winchester model 25 assembly instructions](https://s3.amazonaws.com/mgm-content/sites/armslist/uploads/posts/2020/06/01/11890473_04__winchester_model_70_blue_24_2_640.jpg)
- #Nra winchester model 25 assembly instructions serial numbers
- #Nra winchester model 25 assembly instructions serial number
- #Nra winchester model 25 assembly instructions full
The oval loading/ejection port as described in the text.Īnd the finely ribbed butt-plate with the Savage monogram. The standard front nose-cap, fore-sight and rear-sight from the left-hand side The rear-sight, calibrated from 25 to 200 yards. The bolt: from above and below and the bolt-head face showing extractor and ejector spring. See also: the Savage 1906 magazine patent LONG RIFLE "Īnd from below, with the magazine-way at the front of the trigger-guard fitting, Looking at the post 33 guns on auction sites, I've noticed they were still stamped as Model 19 NRA. In 1933 a better proportioned half stock was adopted, along with other upgrades, including the speed lock feature.
#Nra winchester model 25 assembly instructions full
Up until 1933 these rifles were characterized by a full length military style stock and looked much the same externally (slight variations to the ejection port). These had a single point striker with twin extractors. The later models had barrel studs attaching the mag retaining parts, with the takedown screws attaching to the studs. These also had a double point striker in the bolt. The earlier guns had a smaller trigger pin, and the takedown bolts were longer, attaching directly to the receiver barrel assembly and sandwiching the magazine retaining parts between the stock and barrel/receiver. I found this from copied pages from the Savage 1951 component parts listing (NUMRICH Parts).
#Nra winchester model 25 assembly instructions serial numbers
To differentiate, the models with serial numbers 25,000 to 45,000 were listed as the Model 19 NRA Match Rifle. The earlier guns (serial numbers below 25,000) were listed as the Savage Model 19 O.S. I am still trying to find out what magazine was sent with the guns in 22 SHORT - I have never seen a magazine for one just marked for 22 SHORT.įrom older Savage parts schemtics I found that the Model 19 NRA had 3 major variations, at least in the Savage parts listings. These 1923 versions were also offered in 22 SHORT, not just the early ones. The 1919 NRA was updated in 1923 with the 'new 23A' bolt. It is there on the back edge of the receiver ring. Many people think early 1919s, 22s and 23s have no serial #. These are general rules, as many sub-variants have been encountered, probably due to using left over parts as we also encounter in 99s. Savage model 19 target rifle – pre 1933 NRA target/training rifleġst models had a small rectangular ejection portĢnd models had the oval port, the trigger guard was inletted and the rifle was marked 1919 NRAģrd models had the oval port, trigger guard was not inletted, nor 1919 NRA on the rifle. Our thanks go to the knowledgeable author for his approval of their use, and additional information provided. Italicised notes here are taken from an online forum, discussing the subject rifle,Īnd they succinctly list the salient points for identification and configuration of the models. Respectively in half-inch and one inch bull's eyes.Īn interesting, but perhaps unsurprising claim was thatĪt 100 yards it would outshoot the then current U.S. The groups shown for the rifle at 25 and 50 yards were pictured in the 1919 advertisement
#Nra winchester model 25 assembly instructions serial number
The action, with the serial number stamped between the bolt-handle and the port. "Literary Journal" carried an advertisement introducing the new rifle. See other Savage material: Rifle & Magazine. The NRA (U.S.A.) Model 19 & Model 1933 (19-33) Training & Target Rifles